Circle Mitts - Aran Weight Version

A while ago I knitted the Swiss Cheese Scarf by Winnie Shih from really old yarn that I had bought some time in the 80ies. At that time it had been knitted into a sweater and been frogged several years later. Photos of this scarf project are on its Ravelry page.

I decided to knit a new pair of Circle Mitts (original pattern on my blog) but with the heavier yarn. I had one hank left with a label - from that I infered that the yarn was Aran weight.

This is a short version - for the general construction etc., please refer to the original Circle Mitts pattern.




This work by Knitting and so on is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.



Materials

• 4.5mm needles (I switched from dpns to circulars and back - even if you use circulars, you will need a third needle for the three-needle BO)
• about 50 grams of aran weight yarn
• a tapestry needle to weave in ends

Abbreviations

• kfb: knit front & back
• mk1: make 1 knit stitch
• ssk: slip slip knit
• k2tog: knit 2 sts together
• p2tog: purl 2 sts together
• mk1p: make 1 purl stitch
• p2tog: purl 2 sts together through the back loop
• wrap and turn: a method for short rows

Instructions

Part 1 - Thumb

CO12 and join in round (I used this strechy cast-on method, but other CO methods are fine as well)
Knit 5 rounds of k1 p1-ribbing
Knit 3 rounds of plain stockinette stitch
Row 9: *k2 kfb repeat from * (you have increased by 4 sts => 16 sts on your needles)
Knit 2 more rounds of plain stockinette stitch

Part 2
(basically, you'll increase by 8 sts every other row)
Row 1: *k2 mk1 repeat from * (+8 => 24 sts)
Row 2 (and every other even row during part 2): k
Row 3:  *k1 mk1 k2 repeat from *
Row 5: *mk1 k4 repeat from *
Row 7: *k3 mk1 k2 repeat from *
Row 9: *k5 mk1 k1 repeat from *
BO 5 and continue knitting the round to end

Part 3
Turn work
Row 1: p2tog, * p3 mk1p p4 repeat from * until there are less than 7 sts left, p to last 2 sts, p2togtbl
Row 2: ssk, k to last 2 sts, k2tog
Row 3: p2tog, * p5 mk1p p3 repeat from * until there are less than 8 sts left, p to last 2 sts, p2togtbl
Rows 4 & 5: ssk, k6, wrap and turn, p to last 2 sts , p2togtbl
Row 6: ssk, k to last 2 sts, k2tog
Rows 7 & 8: p2tog, p6, wrap and turn, k to last 2 sts, k2tog
Row 9: p2tog, *p6, mk1p, p3 repeat from * until there are less than 9 sts left, p to last 2 sts, p2togtbl
Row 10: ssk, k to last 2 sts, k2tog
Row 11: p2tog, *p3, mk1p, p7 repeat from * until there are less than 10 sts left, p to last 2 sts, p2togtbl
Row 12: ssk, k to last 2 sts, k2tog

You should now have something like 54 sts on your needles. Hold the sides together and with a three-needle bind-off, BO 15 sts.

If you  want the upper edge to be wider, just insert a few more of the short row sequences (Rows 4 & 5, and 7 & 8). For a more detailed explanations (as well as how to calculate the number of stitches to bind off if the mitts are wider), please read the original pattern.

Part 4
Distribute the remaining 24 stitches on your needles and put the stitch that remained from BO on the first needle. The remaining sts will be knitted in the round.

Round 1: sl1, pick up 2 sts from the gap between the first st and the next one (this will avoid holes), k10, mk1, k4, mk1, k to end, pick up 2 sts from gap between the stitch you just knitted and the first in the round (=> now there are 6 sts more on your needles, i.e. 30)
Row 2: (RS) k12, wrap and turn,
    (WS): p12, p12, wrap and turn (or use another method for short rows, e.g. this)
    (RS): k12
Row 3: (RS) k9, wrap and turn
     (WS): p7 p2tog, p2tog, p7, wrap and turn
     (RS); k9
Row 34 (RS) k5, wrap and turn
     (WS): p5, p5, wrap and turn
     (RS); k5
Round 25: k one round (picking up all wrapped sts).

Part 5
Knit 3 more rounds
Knit 6 rounds of k1 p1-ribbing
Bind-off loosely in pattern

Weave in ends.
Make two.

How to Use This Yarn?

In June I bought a skein of variegated yarn - with colours ranging from white over yellow, orange and red to light- and dark-blue. Here's a selection of my failed attempts, i.e. ideas that I didn't really like - another one is in this blog post :/

Yesterday, I decided that I would try something modular - that way yarn of one colour would be close :) For the modules, I basically used the same almond shape as in the Almendra scarf. But I added a little hole (4 stitches wide) in the center of each "almond". So far, it's the best I've tried with this yarn ... now I only have to decide whether it will be a triangular shawl or a rhomboid wrap ... hmm, difficult ...